Vehicles
Sections
32 not categorized PORSCHE 356C SIDE SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) 96454303602 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Passenger's side fitment.
From $89.00
Make a selection 90161561620EQ This is the round rubber cap that seals the door contact switch. They degrade and become brittle with age and are important as they keep moisture out of the switch. We recommend replacing both at the same time. Sold individually. Left of right side fitment.
$3.30
Make a selection 914501436A Want to replace your battery tray and support, but you see the shelf under it is rusted? You need our replacement shelf. We manufacture this great item, which also mounts the fuel pump and holds the engine to body seal. Easily welded in, it completes a perfect battery area repair. Order some new fuel pump mounts and fuel line grommets while you are at it, and coat with por 15 rust conversion paint before top coating. General Fitment914 1970-76
$409.49
Make a selection 91451231711 This is the large u shaped rear trunk seal that fits around the rear three sides of the rear trunk and seals it from the elements. make sure you check the tail light bodies to rear panel mounting for water leaks before suspecting the rear trunk seal to leak. also check the alignment of the trunk hinges and their pivot cups. View/Change Diagram
From $82.00
Make a selection 91453182110 The "b" part is an excellent reproduction of the original seal. The r and g are originals. this is the seal that fits on the unibody between the rocker carpet and the threshold, this assures a good door seal and no rattles! slightly smaller than the original it is easily installed with a plastic hammer (or a strong heel of the hand!) order the corresponding seal on the door for the tightest fit. View/Change Diagram
From $37.10
Make a selection 91453181410 Genuine outer door seal. an easy way to help seal your interior from the outside elements. a great upgrade for any 914, as they are very commonly broken, cracked, or worn. View/Change Diagram
From $46.64
Make a selection 96454303502 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Driver's side fitment.
From $90.50
Make a selection 91453187310 This nifty item squeezes the water from the side of the window glass and also prevents water from entering the door cavity. easily inchwormed into the gutter using silicone grease order a rear window cap to finish the job. View/Change Diagram
From $6.89
Make a selection 91463196010 This is the perfect aesthetic upgrade for your 70-76 914. replace your old red and cracked usa lenses with these gorgeous italian lenses reproduced to the smallest of detail. italy is the home of gorgeously soulful design, so Porsche had to spice up the 914 to sell them in italy. they were sold from the factory with clear taillight lenses, front turn signals, and side markers. order all three for your own little slice of italy! General Fitment914 1970-76
$249.50
Make a selection 91451231710 This is the large u-shaped rear trunk seal that fits around the rear three sides of the rear trunk and seals it from the elements. make sure you check the tail light bodies to rear panel mounting for water leaks before suspecting the rear trunk seal to leak. also check the alignment of the trunk hinges and their pivot cups. View/Change Diagram
From $38.11
Make a selection GR0890100 Suitable for bonding rubber mouldings to polished, primed or painted metals, wood, various plastics, etc. General FitmentACCESSORY
$29.99
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$14.93
Make a selection ER2081500 Need more camber?elephant racing de-cambered ball joints provide up to 3/4 degree additional negative camber per side. track is widened up to 1/2 inch. The ball joint stud is non-concentric with the housing, effectively lengthening the control arm and pushing the bottom of the strut (and tire) out resulting in added negative camber. Construction includes a true spherical bearing monoball for low-friction, freedom of movement and zero deflection. fully weather-sealed, de-cambered ball joints are a true bolt-in using factory ball joint hardware. General Fitment911 1970-73911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$470.00
Make a selection AAA25600C This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$69.92
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD33150010 Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set. 1 kit is necessary per car. Please note: we recommend this kit for race use, as noise may resonate inside the cabin during street use. For those that are concerned about the noise, please order part # FVD3310212291
$704.00
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection AA500A Our rubber kits are for the perfect restoration. Available only from Automobile Atlanta, this kit consists of everything we use in our restoration shop. General Fitment914 1970-76
$1,021.23
Make a selection WAP52900M19 Windproof, waterproof and breathable thanks to the gore-tex® performance shell. Intricate tape-sealed seams. Waterproof front zip. Reflective piping on the arms and back. Adjustable hem with cord stopper. Three pockets in front section with waterproof zips. Two inside pockets with zips. Porsche motorsport selection logo printed on the left side of the chest area. Sponsors’ logo printed on the right side of the chest area. Large Porsche logo on the back. Outer material: 100% polyester. Lining: 100% polyamide. In white and grey. Sizes: s, m, l, xl, xxl. Limited edition of 911 pieces worldwide. General FitmentACCESSORY
$624.62
Make a selection PCG53160300 This is the small seal behind the door latch base towards the edge of the door. Made of nylonized rubber, this seal will never shrink or split. Sold each, fits left or right side. General Fitment914 1970-76
$4.77
Make a selection WAP52900S19 Windproof, waterproof and breathable thanks to the gore-tex® performance shell. Intricate tape-sealed seams. Waterproof front zip. Reflective piping on the arms and back. Adjustable hem with cord stopper. Three pockets in front section with waterproof zips. Two inside pockets with zips. Porsche motorsport selection logo printed on the left side of the chest area. Sponsors’ logo printed on the right side of the chest area. Large Porsche logo on the back. Outer material: 100% polyester. Lining: 100% polyamide. In white and grey. Sizes: s, m, l, xl, xxl. Limited edition of 911 pieces worldwide. General FitmentACCESSORY
$624.62
Make a selection WAP530XXL19 Windproof, waterproof and breathable featuring gore-tex® performance shell with comfort mapping technology. Intricate tape-sealed seams. Extremely comfortable due to a combination of gore-tex® laminates designed to meet the body’s various needs. . Two pockets on the front with waterproof zips. Reflective piping on the front and back. Adjustable seam with cord stopper. Reflective Porsche logo. Inside pocket with zip. Black. General FitmentACCESSORY
$660.00
Make a selection AA500 Available only from Automobile Atlanta, this kit consists of parts that we use in our restoration shop without going overboard. General Fitment914 1970-76
$629.26
Make a selection WAP53000S19 Windproof, waterproof and breathable featuring gore-tex® performance shell with comfort mapping technology. Intricate tape-sealed seams. Extremely comfortable due to a combination of gore-tex® laminates designed to meet the body’s various needs. . Two pockets on the front with waterproof zips. Reflective piping on the front and back. Adjustable seam with cord stopper. Reflective Porsche logo. Inside pocket with zip. Black. General FitmentACCESSORY
$660.00
Make a selection 91151192302EQ1 This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. This is a high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$136.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |